Donjoy
-
Mix proof Butterfly Valve Type A
- Size: DN25-DN100, 1″- 4″
- Material: 1.4404 / 1.4301, 304/ 316L
- Maximum Temperature: -10 ℃ – 130 ℃
- Maximum Pressure: 10bar
- Operation: Pneumatic/ Manual interchangeable
- Control Box: C-TOP Basic type, C-TOP + AS-I communication
- Seal: EPDM (standard) FPM / SILICON / NBR, FDA177.2600
-
Mix proof Butterfly Valve type B
- Size: DN25-DN100, 1″- 4″
- Material: 1.4404 / 1.4301,304 / 316L
- Maximum Temperature: -10 ℃ – 130 ℃
- Maximum Pressure: 10bar
- Operation: Pneumatic/ Manual interchangeable
- Control Box: C-TOP Basic type, C-TOP + AS-I communication
- Seal: EPDM (standard) FPM / SILICON / NBR, FDA177.2600
- Both sides of the valve body are interchangeable (no matter what connection)
- Contact With Material: AISI 316L / 1.4404
- Connection: SMS, RJT, DIN, 3A, ISO
-
Mixproof tank bottom valve
- Size: DN40-1.1/2″to DN100-4″
- The valve is equipped with a normally closed pneumatic actuator
- Forged ball of the valve body
- If there is a gush of fluid leaks from bottom of valve tube, you can determine whether the seal is damaged
- Easy to remove( just removing the clamps is enough)
- Welded connection (mm or inch)
- Balance Protection Design
- Max.Operating Pressure：10bar
- Min.Operating Pressure：Absolute vacuum
- Working temperature：-10℃ – 130℃(140℃ For short periods or disinfection)
- Certificate：3-A-85-03，PED/97/23/EC,FDA177.2600
-
Mixproof valve / double seat valve
- Size：DN40-1.1/2″ to DN100-4″
- Material：ASTM 316L,1.4404
- Pressure：10bar
- Temperature：130℃
- Gaskets：EPDM,FPM,FDA177.2600
- Surface finish：Ra≤0.8μm
- Air supply：5-7bar
- Certificate：3-A-85-03，PED/97/23/EC,FDA177.2600
- Power Supply ：DC 24V±10%
- Single-acting (standard), double acting (option)
- Self-adjusting valves feature feedback
- Supports analog signal (4-20mA) & amp; electrical signal (DC24V) Output
- Support AS-I BUS
- Supports manual and automatic operation
-
Mixproof valve / double seat valve 2
- Size:DN40-1.1/2″to DN100-4″
- The valve is equipped with a normally closed pneumatic actuator
- Forged ball valve body
- If there is a gush of fluid leaks from bottom of valve tube, you can determine whether the seal is damaged
- Easy to remove( just removing the clamps is enough)
- Welded connection (mm or inch)
- Balance Protection Design
- Max.Operating Pressure：10bar
- Min.Operating Pressure：Absolute vacuum
- Working temperature：-10℃ – 130℃(140℃ For short periods or disinfection)
- Certificate：3-A-85-03，PED/97/23/EC,FDA177.2600
- Compressed air pressure：5bar-7bar
- Gas connection：R1/8″(BSP)
-
Mixproof valve manifold
- Size：1.5″-DN40 to 4″-DN100
- Manifold：from 4 up to 48 valves
- Temperature：130℃
- Pressure：10bar
- Air supply：5-7bar
- With a simple C-TOP on every pneumatic actuator (solenoids and sensors)
- With a C-TOP of AS-I field bus
- Without C-TOP, solenoids are installed in the control panel and sensors on the pneumatic actuator
- PLC control
- The states of the valves can be displayed on the control panel
-
Pneumatic Tank Bottom Diaphragm Valves
- Size: 1″-4″, DN25-DN100
- Highest Temperature: -30 ℃ to 150 ℃ (Depending on diaphragm) (Stainless steel actuator)
- Highest Temperature: -30 ℃ to 130 ℃ (Depending on diaphragm) (Plastic actuator)
- Maximum Pressure: Unidirectional (DELTA P = 100%)
- Normally closed rubber 8bar, PTFE 6bar (option)
- Normally closed rubber 6bar, PTFE 4.5bar (standard)
- Normally open and double acting rubber 8bar, PTFE 6bar
- Facelift different actuators can meet higher pressure rating
- Forged Body: 1.4404 / 316L /1.4435 NB2
- Cast body: 1.4404 / 316L
- Connection: Weld, Clamp, Flange, Thread
- Body Structure: 2 channels, 3 channels, etc.
- Diaphragm Material: EPDM + PTFE (double layer) / EPDM / Silicon / FPM (Viton)
- Certificate: 3A-54-02 / 1580, PED 97/23 EC, FDA177.2600
-
U type Three way Diaphragm Valve U-B
- Size: 1″-4″, DN25-DN100
- Pressure: 10bar (145 PSI)
- Material: ASTM 316L, 1.4404,1.4435 NB2 Fe <0.5%
- Temperature: -20 ℃ + 150 ℃
- Connection: Clamp, Weld, Thread, 3A BPE DIN SMS IDF ISO
- Body Structure: U type tee + sampling valve; U-type links
- Diaphragm Material: EPDM + PTFE (double layer) / EPDM / Silicon / FPM (Viton)
- Certificate: 3A-54-02 / 1580, PED 97/23 EC, FDA177.2600
-
U type Three way Diaphragm Valve U-C
- Size: 1″-4″, DN25-DN100
- Pressure: 10bar (145 PSI)
- Material: ASTM 316L, 1.4404,1.4435 NB2 Fe <0.5%
- Temperature: -20 ℃ + 150 ℃
- Connection: Clamp, Weld, Thread, 3A BPE DIN SMS IDF ISO
- Body structure: U type tee + sampling valve; U-type links
- Diaphragm material: EPDM + PTFE (double layer) / EPDM / Silicon / FPM (Viton)
- Certificate: 3A-54-02 / 1580, PED 97/23 EC, FDA177.2600
-
U-type Three way Mini Diaphragm Valve
- Size: 1/4″-3/4″, DN6-DN15
- Standard: BPE 3A DIN ISO IDF
- Certificate: PED/97/23/EC，3A/54-04/1580，FDA.177.2600
- Max Temperature: -30 ℃ to 150 ℃ (Depending on seal material)(Stainless steel actuator)
- Max Temperature: -30 ℃ to 130 ℃ (Depending on seal material)(Plastic actuator)
- Max Pressure: One way (DELTA P=100%)
- EPDM8bar, PTFE 6 bar(Option)
- EPDM6bar, PTFE 4.5 bar(Option)
- Double action EPDM 8bar, PTFE 6bar
- Assembling different actuators can meet higher pressure rating.
- Forged Body: 1.4404/316L/1.4435 BN2
- Cast Body: 1.4404/316L
- Connection : Clamp, Weld, Thread, Flange
- Operations: Manual and pneumatic
-
Various Combinations Diaphragm Valve
- Size: 1/4″-3/4″，DN6-DN15
- Standard: BPE 3A DIN ISO IDF
- Certificate: PED/97/23/EC，3A/54-04/1580，FDA.177.2600
- Max Temperature: -30 ℃ to 150 ℃ (Depending on seal material)(Stainless steel actuator)
- Max Temperature: -30 ℃ to 130 ℃ (Depending on seal material)(Plastic actuator)
- Max Pressure: One way (DELTA P=100%)
EPDM 8bar, PTFE 6 bar(Option)
EPDM 6bar, PTFE 4.5 bar(Option)
Double action EPDM 8 bar, PTFE 6 bar - Assembling different actuators can meet higher pressure rating.
- Forged Body: 1.4404/316L/1.4435 BN2
- Cast Body: 1.4404/316L
- Connection: Clamp, Weld, Thread, Flange
- Operations: Manual and pneumatic
-
Weld Combined Multi port Diaphragm Valve
- Size: 1/2″-4″, DN6-DN100
- Material: 316L/1.4404，1.4435 NB2 Fe＜0.5%
- Temperature: -20℃ +150℃
- Pressure: 10bar
- Inner Surface Treatment: Ra0.4μm, Mechanical polishing, Electro polishing
- Diaphragm: Double diaphragm: EPDM+PTFE; Single Mdiaphragm: EPDM, FPM, Silicon
- Operating: Manual/ Pneumatic
- Control: configurable, 1) Control Unit C-TOP, 2) positioner IL-TOP, 3) mechanical valve regulator, 4) Position Sensor