ติดต่อสามถามข้อมูลเพิ่มเติม
รับคำปรึกษาจากทีมงานเราได้ง่าย ทีมงานเรายินดีให้คำปรึกษา และจะติดต่อกลับโดยเร็วที่สุด..
-
FA-515 Ex – เซนเซอร์วัด Dew Point (Dew Point Sensor) พร้อมมาตรฐาน ATEX
Features
Dew point sensor FA 515 Ex
measures the Dew point or Pressure dew point in potentially explosive areas and can be used in many non-aggressive Gases.
Typical areas of application: Compressed air, Argon, Nitrogen, Biogas, Natural gas, Hydrogen, etc.
Our Dew point sensor FA 515 Ex fulfils the following industry approvals:
- ATEX II 2G Ex ib IIC T4 Gb Zone 1, gas, Intrinsically safe, temp. 135 °C
- ATEX II 2D Ex ib IIIC T80°C Db Zone 21, dust, intrinsically safe, temp. 80 °C
Please note: The FA 515 Ex may only be operated in conjunction with approved transmitter power supplies or safety barriers or galvanic isolating elements with max:
- Ui = 28 V max.
- Ii = 95 mA max.
- Pi = 0.65 W max.
Details
- Robust design
- Pressure-resistant up to 500 bar
- Long-term stable humidity sensor, proven for years
- 4…20 mA Analogue output in 2-wire technology
- Additional Measured values adjustable via Software: % rH, g/m³, mg/m³, Ppm V/V, g/kg
- Explosion protection according to ATEX / safety in hazardous areas
- NEW: Higher resolution of the Sensor signal thanks to improved evaluation electronics
-
IAC 500 sensor for measuring ambient conditions
Features
IAC 500 sensor for measuring ambient conditions
IAC 500– Measures ambient conditions in the room – absolute pressure, room temperature, humidity.
- Monitoring the intake air of compressed air stations
- Monitoring of room air e.g. cold rooms, storage rooms or clean rooms
The delivery rate of compressors depends on the intake air.
The installation site and the climatic conditions must already be taken into account when designing compressed air stations.
Large temperature fluctuations, e.g. between day and night, lead to uneven compressed air flow.
Details
- 3 in 1 sensor: absolute pressure, temperature and humidity in the room
- Modbus-RTU, Ethernet or M-Bus interface
- Alarm relay – limit value adjustable via buttons (max 60 VDC, 0.5 A)
- Optional: 2 x 4…20 mA analogue outputs, 2 x alarm relays, e.g., for dew point and temperature
[penci_button link=”https://page.line.me/006xhmgy” icon=”fa fa-comments” icon_position=”left” target=”_blank”]ขอใบเสนอราคา[/penci_button] [penci_button link=”/wp-content/uploads/2023/06/KUGA-KGB4-Pressure-Gauge-Rev-A.pdf”]ดาวน์โหลด Catalog[/penci_button]
-
Intelligent chart recorder DS 500 for compressed air and gases
Features
Intelligent chart recorder DS 500 for compressed air and gases
From recording of the measured data, indication on a big colour screen, alerting, storage up to remote read-out via webserver… this is all possible with DS 500. By means of the CS Soft Basic software alarms can be sent via SMS or e-mail. All measured values, measured curves and threshold exceedings are indicated. The curve progressions from the beginning of the measurement can be viewed by an easy slide of the finger. Daily/weekly/monthly reports with costs in € and counter reading in m³ for each consumption sensor are completing the sophisticated system concept. The big difference to odinary paperless chart recorders reveals in the easy initiation and in the evaluation of the measured data. All sensors are identified directly and powered by DS 500. Everything is matched and tuned
Details
- Clear layout: 7″ colour screen with touch panel
- Versatile: Up to 12 optional sensors can be connected
- Suitable for industrial applications: Metal housing IP 65 or panel mounting
- Data avialable though world wide web: Network-compatible and remote transmission via webserver
- Intelligent: Daily/weekly/monthly reports
- Mathematical function for internal calculations
- Totalizer function for analogue signals
- Saves time and costs during installation
- e.g. the typical figures of a compressed air plant:
- costs in € per generated m³ air
- kwh/m³ generated air
- consumption of single lines including summation
e.g. 0/4…20 mA, 0…10 V. In case of third-party sensors which e.g. only give a 4…20 mA signal for the actual flow in m³/h a total counter reading in m³ can be generated by means of the totalizer function.
[penci_button link=”https://page.line.me/006xhmgy” icon=”fa fa-comments” icon_position=”left” target=”_blank”]ขอใบเสนอราคา[/penci_button] [penci_button link=”/wp-content/uploads/2023/06/KUGA-KGB4-Pressure-Gauge-Rev-A.pdf”]ดาวน์โหลด Catalog[/penci_button]
-
Intelligent mobile chart recorder – DS 500 mobile
Features
Intelligent mobile chart recorder – DS 500 mobile
If we talk about operational costs of compressed air plants we are actually talking about the energy costs as they make up about 70 to 80 % of the total costs of a compressed air plant. Depending on the size of the plant this means considerable operating costs. Even in smaller plants this may quickly add up to 10 000 to 20 000 € per year. This is an amount which can be considerably reduced – even in case of well operated and maintained plants. For sure this also applies to your compressed air plant! Which actual costs per generated m³ air do you actually have? Which energy is gained due to the waste heat recovery? What is the total performance balance of your plant? How high are the differential pressures of single filters? How high is the humidity (pressure dew point)? How much compressed air is used? By means of the intelligent chart recorder DS 500 mobile and the suitable sensors and meters all these questions can be answered easily. For example by means of a long-term measurement over 7 days, data recording and evaluation at the PC.
Details
- Easy and clear layout: Very easy operation via 7″ color display with touch panel
- Versatile: Up to 12 sensors/meters connectable also third-party sensors/meters including power supply
- Reliable: Stores all measured values on a memory card, easy reading-out via USB stock possible
- Intelligent energy analysis: Daily/weekly/monthly evaluations mathematic function for internal calculations, e.g. the typical key data of a compressed air plant:
- costs in € per generated m³ air
- kWh/m³ generated air
- flow of single lines including summation
[penci_button link=”https://page.line.me/006xhmgy” icon=”fa fa-comments” icon_position=”left” target=”_blank”]ขอใบเสนอราคา[/penci_button] [penci_button link=”/wp-content/uploads/2023/06/KUGA-KGB4-Pressure-Gauge-Rev-A.pdf”]ดาวน์โหลด Catalog[/penci_button]
-
M-Bus – Industrial gas meter
Features
M-Bus – Industrial gas meter
CS INSTRUMENTS GmbH & Co. KG was the OEM manufacturer of ENDYS AIR Gas meters with M-Bus from 2010 to the end of 2017. ENDYS AIR products were previously marketed exclusively by Hochhut GmbH, which is now working with another manufacturer. CS INSTRUMENTS GmbH & Co. KG is now offering the successor to the successful Gas meter itself.
The improved successor to the ENDYS AIR Gas meter now offers all the options for digitalising your Flow measurement for a wide range of industrial gases and is the ideal consumption meter for Industry 4.0.
Our M-Bus flow meters have been metrologically improved and completely revised. In addition to the M-Bus interface, the measuring devices also have the following additional outputs and bus systems:
- Modbus RTU
- Modbus TCP or TCP PoE
- Profibus, Profinet
- 4…20 mA and Pulse
- Hart ( in preparation)
The VA 520, VA 500, VA 550 and VA 570 gas meters with M-Bus are therefore the ideal M-Buscompressed air meters or M-Bus gas meters for industrial gases such as Natural gas, Biogas, Methane, Nitrogen, Argon, Carbon dioxide, etc.
The Flow meters with M-Bus are perfectly suited for retrofitting, upgrading and new installation of Gas meters, compressed air meters and Flow measurement devices to existing and upcoming building management systems and energy management software in accordance with DIN ISO 50001 and DIN ISO 16247.
Please contact us if you have any questions regarding our new M-Bus product line.
Details
- Direct display in Nm3/h, or NI/min and temperature in C°
- Calorimetric measuring principle – no additional pressure and temperature measurement necessary
- High measurement accuracy ¼ to 3 inches
- VA 500 and VA 550 insert version from ½ inch to DN 400 / DN 500
[penci_button link=”https://page.line.me/006xhmgy” icon=”fa fa-comments” icon_position=”left” target=”_blank”]ขอใบเสนอราคา[/penci_button] [penci_button link=”/wp-content/uploads/2023/06/KUGA-KGB4-Pressure-Gauge-Rev-A.pdf”]ดาวน์โหลด Catalog[/penci_button]
-
PI 500 for e.g. portable flow measurement
Features
PI 500 for e.g. portable flow measurement
The portable flow meter PI 500 is an all-purpose hand-held measuring instrument for many compressed air and gas applications in industry like e.g.:
- Flow measurement
- Pressure-/ vacuum measurement
- Temperature measurement
- Moisture/ dew point measurement
The graphic indication of coloured measurement curves is inimitably. Up to 100 million measured values can be stored with date and name of measuring site. The measured values can be transferred to the computer by means of a USB stick. The data can be comfortably evaluated with the CS Soft Basic software. Measured data and service reports can be issued easily and quickly. The following sensors can be connected to the freely configurable sensor input of PI 500:
- Pressure sensors (high and low pressure)
- Flow sensors, VA 500 / VA 520
- Temperature sensors Pt 100, Pt 1000 / 4…20 mA
- Dew point sensors FA 510 / FA 515
- Effective power meters
- Opitonal third-party sensors with the following signals: 0…1/10 V, 0/4…20 mA, Pt 100, Pt 1000, pulse, Modbus
Details
- Universal sensor input for lots of common sensor signals
- Internal rechargeable Li-Ion batteries (approx. 12h continuous operation)
- 3.5″ graphic display / easy operation via touch screen
- Integrated data logger for storage of the measured values
- USB interface for reading out via USB stick
- International: Up to 8 languages selectabel
[penci_button link=”https://page.line.me/006xhmgy” icon=”fa fa-comments” icon_position=”left” target=”_blank”]ขอใบเสนอราคา[/penci_button] [penci_button link=”/wp-content/uploads/2023/06/KUGA-KGB4-Pressure-Gauge-Rev-A.pdf”]ดาวน์โหลด Catalog[/penci_button]
-
VA 409 – Flow direction switch for compressed air systems
Features
VA 409 – Flow direction switch for compressed air systems
The new thermal flow direction switch VA 409 with direction indication serves for determination of the flow direction of compressed air and gases especially in closed circular pipelines.
By means of VA 409 with flow direction indication the flow direction of the compressed air can be determined quickly and safely. Compared with the former mechanical paddle flow switches VA 409 is able to detect even the smallest changes in the flow direction quickly and without any mechanical movement.
The direction information in form of a potential-free contact (normally closed max. 60 VDC, 0.5 A) is transferred to the consumption sensors VA 500/ VA 520 or to a separate building management system (mbs). Two LEDs show the flow direction.
In connection with 2 consumption sensors VA 500/ VA 520 incoming and outflowing compressed air in closed circular pipelines can be measured precisely.
Details
- Detects smallest changes <0.1 m/s referred to 20°C and 1000 mbar
- No mechanical wear parts
- Easy installation under pressure
[penci_button link=”https://page.line.me/006xhmgy” icon=”fa fa-comments” icon_position=”left” target=”_blank”]ขอใบเสนอราคา[/penci_button] [penci_button link=”/wp-content/uploads/2023/06/KUGA-KGB4-Pressure-Gauge-Rev-A.pdf”]ดาวน์โหลด Catalog[/penci_button]
-
VA 500 – Flow meter for compressed air and gases
Features
VA 500 – Flow meter for compressed air and gases
Recording and reducing energy costs and CO2 emissions while increasing the sustainability of any compressed air system. With our VA500 it is possible to monitor your consumption and analyze your leakage flows with just one measuring device. Due to its design, it is also ideal for mobile measurements.
Details
- Measurement of mass flow direct output of standard volume flow
- Highly accurate at small as well as higher flow rates
- Pressure and temperature compensated by the thermal mass flow principle
- Quick and easy installation via a ½” ball valve
- No moving parts, thus low maintenance
- Vanishingly low pressure drop due to vanishingly low blockage of the diameter
- Can be used for compressed air and non-corrosive gases such as nitrogen, oxygen, argon, helium, etc.
- 04…20 mA, pulse and a Modbus RTU (RS 485) interface as standard.
- Optional: Interfaces such as Modbus TCP (Ethernet), PoE, M-Bus
- Optional: Bi-directional measurement
- Pressure tight up to 50 bar
- Temperature range up to 110°C
- Protection class IP65
- Integrated display for showing the measured values
- Can be used from 1/2″ up to 40″, larger diameters on request
- Easy installation under pressure
- Settings can be changed via the display
- Main counter reading can be reset via the display
- Suitable for gas velocities up to 224 Nm/s
- Highly precise with an accuracy of ± 1.5% or ± 1% of the measured value ± 0.3% of the final value
[penci_button link=”https://page.line.me/006xhmgy” icon=”fa fa-comments” icon_position=”left” target=”_blank”]ขอใบเสนอราคา[/penci_button] [penci_button link=”/wp-content/uploads/2023/06/KUGA-KGB4-Pressure-Gauge-Rev-A.pdf”]ดาวน์โหลด Catalog[/penci_button]
-
VA 520 – Thermal mass flow meter for flow measurement
Features
VA 520 – Thermal mass flow meter for flow measurement
Record and reduce your energy costs and increase your sustainability with the VA 520. Monitor your consumption and analyze your leakages with a permanently installed flow meter in distribution stations, in front of individual departments or for billing purposes of individual consumers.
Details
- Measurement of mass flow rate, output of standard volume flow rate
- High accuracy for both small and large flows
- Pressure and temperature compensated by the thermal mass flow principle
- Easy installation and removal of the sensor, the integrated measuring section can remain in the line for cleaning or
- recalibration of the sensor and can simply be closed with a sealing cap
- No moving parts, therefore low maintenance
- Vanishingly low pressure loss due to vanishingly low blockage of the diameter
- Can be used for compressed air and non-corrosive gases such as nitrogen, oxygen, argon, helium, etc.
- 04…20 mA, pulse and a Modbus RTU (RS 485) interface as standard, optional interfaces such as Modbus TCP (Ethernet), PoE, M-Bus
- Optional interfaces such as Modbus TCP (Ethernet), PoE, M-Bus
- Optional: Bi-directional measurement
- Pressure range up to 40 bar
- Temperature range from -30 to 80°C
- Protection class IP65
- Integrated display to show the measured values
- Can be used from DN 8 to DN 80
- Settings adjustable via the keys of the display
- Main counter reading can be reset via the display
- For velocities up to 224 Nm/s
- Highly accurate with an accuracy of ± 1.5% or ± 1% of the measured value – as well as ± 0.3% of the final value
[penci_button link=”https://page.line.me/006xhmgy” icon=”fa fa-comments” icon_position=”left” target=”_blank”]ขอใบเสนอราคา[/penci_button] [penci_button link=”/wp-content/uploads/2023/06/KUGA-KGB4-Pressure-Gauge-Rev-A.pdf”]ดาวน์โหลด Catalog[/penci_button]
-
VA 521 – Compact Inline flow meter for compressed air and other gas types
Features
VA 521 – Compact Inline flow meter for compressed air and other gas types
Reduce your energy costs and increase your sustainability with the VA 521. Monitor the consumption of each machine and analyze your leakage flows with just one measuring device.
Details
- Measurement of mass flow rate, output of standard volume flow rate without additional measurement of pressure and temperature.
- Compact device for installation in limited space, no inlet and outlet sections necessary due to the integrated flow straightener
- Highly accurate at small as well as high flowrates
- Easy installation and removal of the sensor, the integrated measuring section can remain in the line for cleaning or recalibration of the sensor and can simply be closed with a sealing cap
- No moving parts, therefore low maintenance required
- Can be used for compressed air and non-corrosive gases such as nitrogen, oxygen, argon, helium, etc.
- 04…20 mA, pulse and a Modbus RTU (RS 485) interface as standard
- Optional interfaces: Modbus TCP (Ethernet), PoE, M-Bus
- Pressure range up to 40 bar
- Temperature range up to 80°C
- Integrated display to show the measured values
- Available from ½” to 2”
- Settings adjustable via the keys of the display
- Main counter can be reset via the display
- For velocities up to 224 Nm/s
- Extremely precise with an accuracy of ± 1.5% or ± 1% of the measured value – as well as ± 0.3% of the final value
[penci_button link=”https://page.line.me/006xhmgy” icon=”fa fa-comments” icon_position=”left” target=”_blank”]ขอใบเสนอราคา[/penci_button] [penci_button link=”/wp-content/uploads/2023/06/KUGA-KGB4-Pressure-Gauge-Rev-A.pdf”]ดาวน์โหลด Catalog[/penci_button]
-
VA 525 – Compact Inline flow meter for compressed air and nitrogen
Features
VA 525 – Compact Inline flow meter for compressed air and nitrogen
The innovative VA 525 combines modern digital interfaces for connection to an energy monitoring system with a small, compact design. The VA 525 is always used when many machines (compressed air consumers) have to be integrated into an energy monitoring network.
Reduce your energy costs and increase your sustainability with the VA 525 compact sensor. Monitor the consumption of individual machines and analyze your leakage flows with just one measuring device.
Details
- Measurement of mass flow rate, output of standard volume flow rate without additional measurement of pressure and temperature
- Compact device for installation in limited space, no inlet and outlet sections necessary thanks to integrated flow straightener
- Available with built-in pressure sensor
- Highly accurate at small as well as large flows
- No moving parts, therefore low maintenance
- Applicable for compressed air and nitrogen
- 04…20 mA and pulse or a Modbus RTU (RS 485) interface as standard
- Optional interfaces such as Modbus TCP (Ethernet), PoE, M-Bus available
- Pressure range up to 16 bar
- Temperature range up to 60°C
- Integrated display to show the measured values
- Available from 1/4″ to 2”
- Settings adjustable via the keys of the display
- Main counter can be reset via the display
- For speeds up to 224 Nm/s
- Highly accurate with an accuracy of ± 1.5% or ± 1% of the measured value – as well as ± 0.3% of the final value
[penci_button link=”https://page.line.me/006xhmgy” icon=”fa fa-comments” icon_position=”left” target=”_blank”]ขอใบเสนอราคา[/penci_button] [penci_button link=”/wp-content/uploads/2023/06/KUGA-KGB4-Pressure-Gauge-Rev-A.pdf”]ดาวน์โหลด Catalog[/penci_button]
-
VA 550 – Thermal mass flow sensor for flow measurement
Features
VA 550 – Thermal mass flow sensor for flow measurement
Record and reduce your energy costs and increase your sustainability with the VA 550. Monitor your Consumption and analyse your leakage flows with just one measuring device. Due to its design, it is also ideal for Portable Measuring.
Details
- All wetted parts are made of stainless steel, especially for applications with high demands on cleanliness and surface quality
- Robust aluminium housing enables use in harsh industrial environments
- Recommended for flammable gases such as Natural gas, hydrogen, Biogas, etc. due to ATEX or DVGW approval
- Measuring the mass flow, direct output of the Standarized volume flow
- Highly accurate for both small and large flows
- Pressure and temperature-compensated thanks to the thermal mass flow principle
- Quick and easy installation via a standard ½” Ball valve
- No moving parts, therefore Low maintenance
- Disappearingly low pressure loss, as the blockage of the diameter is negligible
- 04…20 mA, pulse and a Modbus RTU (RS 485) interface as standard, optional interfaces such as Modbus TCP (Ethernet), PoE, M-Bus
- Pressure range up to 50 bar, special version up to 100 bar
- Media temperature range up to 180 °C (ATEX version up to 120 °C)
- Protection class IP 67 (IP 64 for ATEX II 2D Ex tb IIIC T90°C Db)
- Integrated display for showing the Measured values
- Suitable as insertion version for 3/4″ to DN 1000
- Simple installation under pressure
- Settings can be adjusted using the buttons on the display
- Main counter reading can be reset via the Display
- For Velocities up to 224 Nm/s
- Highly accurate with an Accuracy of ± 1.5% or ± 1% of the Measured value – As well as ± 0.3 % of the final value
[penci_button link=”https://page.line.me/006xhmgy” icon=”fa fa-comments” icon_position=”left” target=”_blank”]ขอใบเสนอราคา[/penci_button] [penci_button link=”/wp-content/uploads/2023/06/KUGA-KGB4-Pressure-Gauge-Rev-A.pdf”]ดาวน์โหลด Catalog[/penci_button]
-
VA 570 – Thermal mass flow meter for consumption measurement
Features
VA 570 – Thermal mass flow meter for consumption measurement
Record and reduce your energy costs and increase your Sustainability with the VA 570 flow meter. Monitor your Consumption and analyse your leakage rate with a permanently installed flow meter in distribution stations, in front of individual departments or for billing purposes of individual Consumers.
Details
- Measuring the mass flow, direct output of the Standarized volume flow possible without additional measurement of Pressure and Temperature
- All wetted parts of the VA 570 are made of stainless steel, especially for applications with high demands on purity and surface quality
- The Robust aluminium housing is ideal for harsh industrial conditions as well as outdoor installations
- No moving parts, therefore Low maintenance
- Disappearingly low pressure loss, as the blockage of the diameter is negligible
- ATEX or DVGW certification available, therefore recommended for gases such as Natural gas, hydrogen, Biogas, etc.
- Highly accurate for both small and large flows
- Pressure and temperature-compensated thanks to the thermal mass flow principle
- Easy installation and removal of the sensor from the measuring section, the measuring section can remain in the line for cleaning or recalibration of the sensor and can simply be closed with a cap
- For Velocities up to 224 Nm/s
- Media temperature range up to 180 °C (ATEX version up to 120 °C)
- Maximum pressure 16 bar, up to 40 bar in the PN 40 special version
- Can be used from DN15 to DN 80
- Highly accurate with an Accuracy of ±1.5% or ±1% of Measured value, as well as ±0.3% of final value
- 04…20 mA, pulse and a Modbus RTU (RS 485) interface as standard, optional interfaces such as two galvanically isolated analogue outputs (04…20 mA), Modbus TCP (Ethernet), PoE, M-Bus
- Protection class IP 67 (IP 64 for ATEX II 2D Ex tb IIIC T90°C Db)
- Integrated display for showing the Measured values
- Settings can be changed using the buttons on the Display
- Main counter reading can be reset via the Display
[penci_button link=”https://page.line.me/006xhmgy” icon=”fa fa-comments” icon_position=”left” target=”_blank”]ขอใบเสนอราคา[/penci_button] [penci_button link=”/wp-content/uploads/2023/06/KUGA-KGB4-Pressure-Gauge-Rev-A.pdf”]ดาวน์โหลด Catalog[/penci_button]
-
VD 500 – Flow sensor for wet compressed air
Features
VD 500 – Flow sensor for wet compressed air
Reduce your energy costs and increase your efficiency with the VD 500. Suitable directly for measurement after the compressor. Monitor the delivery rate of your compressor and create a FAD analysis.
- Measurement immediately downstream of the compressor
- Measurement at high temperatures
Details
- thus covers the complete operating range of variable speed drive (VSD) compressors
- Particularly suitable for extremely high flow rates
- Flow, total consumption, temperature and pressure
- Measurement at high temperatures, max. temperature 180 °C
- Can be used in pipes from DN 20 to DN 600
- Installation via 1/2″ ball valve under pressure
- Measurement of the capacity of compressors
- Compressed air audits
- Efficiency measurement of compressed air systems
- After functioning water separator
- In horizontal lines (recommended) or in risers
- 04…20 mA, pulse and a Modbus RTU (RS 485) interface as standard
- Optional interfaces like Modbus TCP (Ethernet), PoE, M-Bus
- Pressure range up to 30 bar
- Temperature of the medium -30 ° … +180 °C
- Integrated display to show the measured values
- Available from DN20 to DN500
- Easy installation under pressure
- Settings adjustable via the keys of the display
- Main counter reading can be reset via the display
- Can be used for velocities up to 600 Nm/s
- High accuracy with 1.5% deviation of the measured value
[penci_button link=”https://page.line.me/006xhmgy” icon=”fa fa-comments” icon_position=”left” target=”_blank”]ขอใบเสนอราคา[/penci_button] [penci_button link=”/wp-content/uploads/2023/06/KUGA-KGB4-Pressure-Gauge-Rev-A.pdf”]ดาวน์โหลด Catalog[/penci_button]
-
VD 520 – Inline flow meter
Features
VD 520 – Inline flow meter
- Ready-to-use compact design to minimise installation effort – therefore no volume corrector required
- Provides Flow, Total consumption, Temperature and Pressure
- Differential pressure sensor element with unique sensitivity, measures highly accurately at < 2 m/s
- Large flow measuring range with extended measuring span thanks to the use of measuring sections with a reduced inner diameter
- Smaller inlet sections due to the use of an averaging pitot tube
- Robust design, no moving parts
- Sensor head can be removed for calibration
Details
Area of application:
- Wet compressed air
- Technical gases
- Mixed gases: e.g. Natural gas/H2
- LPG
- propane
- CO2
[penci_button link=”https://page.line.me/006xhmgy” icon=”fa fa-comments” icon_position=”left” target=”_blank”]ขอใบเสนอราคา[/penci_button] [penci_button link=”/wp-content/uploads/2023/06/KUGA-KGB4-Pressure-Gauge-Rev-A.pdf”]ดาวน์โหลด Catalog[/penci_button]
-
VD 550 – Robust Flow sensor for Wet compressed air / gases
Features
VD 550 – Robust Flow sensor for Wet compressed air / gases
- Unrivalled sensitivity in the lower Measuring range:
measures from as little as 2 m/s and thus covers the entire operating range
of speed-controlled Compressors - Particularly suitable for extremely high Flow rates
- Flow, Total consumption, Temperature and Pressure
- Measuring at high temperatures, max. temperature 180 °C
- Can be used in pipes from DN 20 to DN 600
- Installation via 1/2″ Ball valve under Pressure
- Robust impact-resistant die-cast aluminium housing for outdoor use
IP 67
Details
Typical applications:
- Measuring the Capacity of compressors
- Compressed air audits
- Efficiency measurement of Compressedair systems
[penci_button link=”https://page.line.me/006xhmgy” icon=”fa fa-comments” icon_position=”left” target=”_blank”]ขอใบเสนอราคา[/penci_button] [penci_button link=”/wp-content/uploads/2023/06/KUGA-KGB4-Pressure-Gauge-Rev-A.pdf”]ดาวน์โหลด Catalog[/penci_button]
- Unrivalled sensitivity in the lower Measuring range: